Expt. No. 10 Design an industrial fluid power system to address a specified problem by selecting components from manufacturer catalogs.

-

 

Expt. No: 10 Design an industrial fluid power system to address a specified problem by selecting components from manufacturer catalogs.

Aim: Design of simple hydraulic systems used in practice using manufacturers’ catalogue

Theory:

A hydraulic circuit is a group of components such as pumps, actuators, control valves, conductors and fittings arranged to perform useful work. There are three important considerations in designing a hydraulic circuit:

 

1.  Safety of machine and personnel in the event of power failures.

2.  Performance of given operation with minimum losses.

3.  Cost of the component used in the circuit.

 

 

Approach for Solution:

Step1: Draw hydraulic Circuit for given problem.

Step 2: Selection of Cylinder

Step3:  Selection of Pump

Step4: Selection of Oil Reservoir

Step5: Selection for other components

 

Note: - perform the experiment in the groups of 5 students as per your convenience

Problem Statement:



 



 


 Manufacturer Catalogue:- 

 


 


 

 

 

 

 



 

Comments

Post a Comment

Popular posts from this blog

EXPERIMENT NO 5 Measurement of spur gear parameters using Gear Tooth Vernier / Span Micrometer / Gear Rolling Tester

-
Image
 EXPERIMENT NO 5 TITLE: Measurement of gear tooth thickness by gear tooth Vernier Caliper/Constant Chord/Spam micrometer. APPARATUS:  Gear tooth vernier caliper, vernier caliper 12’’ 300 mm, bench vice. THEORY: Brief description of different characteristics of measuring of tooth thickness by gear truth vernier is given. It consists of a horizontal and a vertical vernier scale. It is based on the principle of vernier scale. The thickness of a tooth at pitch line and the addendum is measured by an independent tongue each of which is adjusted independently by adjusting the slide screws on graduated beams. TERMINOLOGY OF GEAR TOOTH (i)    Pitch circle diameter (PCD) : It is the diameter of a circle which by pure rolling action would produce the same motion on the toothed gear wheel. It is equal to D = (T X OD)/(T+2)OD = outside diameter T = number of teeth (ii)    MODULE: It is defined as the length of the pitch circle diameter per truth. ...
Read more

Experiment No 9 Determination of geometry and dimensions of given composite object / single point tool, using profile projector and tool maker’s microscope.

-
Image
  Experiment No. 9 Title: - Experiment on tool maker’s microscope   Aim :- Study and Application of Tool Maker's Microscope .   Apparatus :-Tool maker’s microscope, specimen. Theory: - Introduction:- The tool maker’s microscope is a versatile instrument that measure by optical means with no pressure being involved, thus very useful for measurement on small and delicate parts. It is designed for:   a)    Measurement on parts of complex form e.g. - profile of external thread, tool, templates, gauges, etc. b)    Measuring center to center distance of holes in any plane. c)    A variety of linear measurements. d) Accurate angular measurements.   [1] Use of Tool Makers microscope for screw thread parameter measurement. Use of profile projector for screw thread parameter and slot dimensions measurement. Please see the video animation for working of all the parts of Tool Maker's Microscope   Tool maker’s mi...
Read more

Experiment No 5 Measurement of thread parameters using floating carriage diameter measuring machine.

-
Image
  EXPERIMENT NO 4 TITLE:  Determine Parameters of screw thread using floating carriage micrometer    APPARATUS:  Floating carriage micrometer with all accessories and specimens. THEORY: The measurement of minor diameter is carried out on a floating carriage diameter measuring machine in which threaded work piece is mounted between centers. Such micrometer is constrained to move at right angles to axis of centers by v ball side. If reading on setting cylinder with u-pipe in position R1 and reading R2 and diameter D=Dm+ (R2-R1) reading may be taken at various positions in order to determine the tapers variety. The machine consists of parts:- 1.Base: base casting carries a pair of centre’s on which threaded work piece is mounted 2.Another carriage is mounted on it and exactly 90° to it on this provided carriage is capable of moving towards centre. 3.On this carriage one head having a large thimble enabling reading up to 0.002 mm is provided. Procedure:  ...
Read more